Search Entire Site

Narrow by

Product

Academic Products

Clear all
Product

Tutorial Results

Showing 1-10 of 214 results
Why Does USRP2 Appear Instead of the USRP Device in the NI-USRP Configuration Utility? - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/usrp2-appear-config-utility/
An incorrect IP address on the computer may cause this error. Check the IP address and run the NI-USRP Configuration Utility again. An old FPGA or firmware image on the device may also cause this error. ...
Why Doesn't the USRP Device Appear in MAX? - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/appear-max-usrp-device/
MAX only supports USRP-2940/2942/2943/2944/2945 and USRP-2950/2952/2953/2954/2955 devices configured with a PCI Express connection. If you are using a USRP device configured with an Ethernet connection, ...
Configuring Multiple Devices - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/configuring-multiple-devices/
You can connect multiple devices in the following ways: Multiple Ethernet interfaces—one device for each interface Single Ethernet interface—one device connected to the interface, additional device connected ...
Why do I Receive an Enumeration Error? - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/enumeration-error/
If you are using a desktop computer with the NI-USRP instrument driver successfully installed, it is possible that there is a compatibility issue between your computer and the PCIe card. Complete the following ...
Why Don't NI-USRP Examples Appear in the NI Example Finder in LabVIEW? - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/examples-in-ni-example-finder/
NI-USRP does not install examples into the NI Example Finder. You can access NI-USRP examples from the following locations: LabVIEW From the Start menu at StartAll ProgramsNational InstrumentsNI-USRPExamples. ...
Increasing the Number of Samples - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/increasing-number-of-samples/
Increase the number of samples to achieve greater throughput in Ethernet- and PCIe-based streaming. Complete the following procedure to improve data streaming performance: Increase the number of samples ...
Synchronizing with the NI-USRP Driver - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/synchronizing-usrp-driver/
Complete the following steps to configure and synchronize the MIMO system: Open the receive (RX) session by specifying the IP address of each USRP device. Separate each IP address with a comma. Set the ...
Using NI-USRP in LabVIEW - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/using-ni-usrp-labview/
Complete the following steps to develop an NI-USRP application in LabVIEW: Open an existing or new VI. From the Functions palette, locate the NI-USRP VIs at Instrument I/O Instrument DriverNI-USRP. Select ...
Using NI-USRP in LabVIEW NXG and LabVIEW Communications System Design Suite - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/latest/manual/using-ni-usrp-nxg-comms/
Complete the following steps to develop an NI-USRP application in LabVIEW NXG or LabVIEW Communications System Design Suite: Open an existing or new VI. Select the Diagram tab. From the palette, locate ...
Configuring an MTU Size Greater than 1,500 Bytes - NI-USRP 18.1 Manual www.ni.com/documentation/en/ni-usrp/18.1/manual/configuring-mtu-greater-than-1500-bytes/
To configure a maximum transmission unit (MTU) size greater than 1,500 bytes, complete the following steps: Enable the jumbo frames option of the Ethernet interface card. Select Control PanelNetwork and ...