Search Entire Site

  • Search Within

Search Results

Showing 1-10 of 115 results
Configure Pulse Voltage Limit Range (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/configure-pulse-voltage-limit-range/
Configures a range defining valid values that the pulse voltage limit and pulse bias voltage limit can be set to for the specified channel(s). The pulse voltage limit range setting is applicable only if ...

Configure Trigger (Start » Software Edge) (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/configure-software-edge-start-trigger/
Configures the Start trigger for software triggering. Use the Send Software Edge Trigger node to assert the trigger condition. Not supported niDCPower Configure Software Edge Start Trigger.vi <helpdir>:/NIDCPowerVIRef.chm::/niDCPower_Configure_Software_Edge_Start_Trigger.html ...

Get Calibration User Defined Info (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/get-calibration-user-defined-info/
Returns the user-defined information in the device onboard EEPROM. Not supported niDCPower Get Cal User Defined Info.vi <helpdir>:/NIDCPowerVIRef.chm::/niDCPower_Get_Cal_User_Defined_Info.html session ...

Get Next Coercion Record (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/get-next-coercion-record/
Returns the coercion information associated with the IVI session and clears the earliest instance in which NI-DCPower coerced a value that you specified. Not supported niDCPower Get Next Coercion Record.vi ...

Reset (Reset with Defaults) (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/reset-with-defaults/
Resets the device to a known state and assigns user-defined default values for configurable properties from the IVI configuration. This node disables power generation, resets session properties to their ...

Send Software Edge Trigger (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/send-software-edge-trigger/
Asserts the specified trigger. This node can override an external edge trigger. Related topics: Triggers Not supported This node does not support the following devices: PXI-4110 PXI-4130 niDCPower Send ...

Wait For Event (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/wait-for-event/
Waits until the device has generated the specified event. This node should only be called in the Running state. The session monitors whether each type of event has occurred at least once since the last ...

Abort (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/abort/
Transitions the NI-DCPower session from the Running state to the Committed state. If a sequence is running, the Abort node is stopped. Related Documentation: Programming States Not supported Disabling ...

Adjust Current Limit Calibration (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/adjust-current-limit-calibration/
Calculates calibration constants for the current limit for the specified output channel and range by comparing requested and measured outputs. This node can only be called from an external calibration ...

Adjust Residual Current Offset Calibration (G Dataflow) - NI-DCPower 17.0 Manual www.ni.com/documentation/en/ni-dcpower/17.0/ni-dcpower-node-ref/adjust-residual-current-offset-calibration/
Calculates the calibration constants for the residual current offsets for the specified output channel. This node can be called only in an external calibration session. The node requires that the output ...