Search Entire Site

  • Search Within

Search Results

Showing 1-10 of 106 results
Configure Transducer Type (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/configure-transducer-type/
Configures the transducer type. Not supported Not supported in VIs that run in a web application niDMM Configure Transducer Type.vi <helpdir>:/dmmviref.chm::/niDMM_Configure_Transducer_Type.html session ...

Calibration Utilities - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/calibration-utilities/
Get and set calibration information.

Close External Calibration (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/close-external-cal/
Closes an external calibration session and deallocates reserved resources. Refer to the calibration procedure for your DMM before using this node. Not supported Not supported in VIs that run in a web application ...

Close (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/close/
Closes the session and deallocates reserved resources. Not supported Not supported in VIs that run in a web application niDMM Close.vi <helpdir>:/dmmviref.chm::/niDMM_Close.html session in Instrument identifier ...

Configure AC Bandwidth (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/configure-ac-bandwidth/
Configures frequency properties used for AC measurements. This node affects the DMM only when the Function property is set to an AC measurement. Not supported Not supported in VIs that run in a web application ...

Configuration - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/configuration/
Configuration NI-DMM 17.5, 18.0 NI-DMM 18.1 Configure and control a DMM. Configure AC Bandwidth Configures frequency properties used for AC measurements. Configure ADC Calibration Configures a DMM to compensate ...

Configure Fixed Reference Junction (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/configure-fixed-reference-junction/
Configures the fixed reference junction temperature for a thermocouple with a fixed reference junction type. Not supported Not supported in VIs that run in a web application session in Instrument identifier ...

Configure Measurement Complete Destination (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/configure-meas-complete-dest/
Specifies the destination of the DMM Measurement Complete signal. This signal is issued when the DMM completes a single measurement. This signal is commonly referred to as Voltmeter Complete. Figure out ...

Configure Waveform Acquisition (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/configure-waveform-acquisition/
Configures the DMM for waveform acquisitions. Not supported Not supported in VIs that run in a web application This node is supported by the following modules: PXI-4070 PXI-4071 PXI-4072 PXIe-4080 PXIe-4081 ...

Disable (G Dataflow) - NI-DMM 18.5, 19.0 Manual www.ni.com/documentation/en/ni-dmm/18.5/ni-dmm-node-ref/disable/
Places the DMM in a quiescent state where it has minimal or no impact on the system to which it is connected. If a measurement is in progress when this node runs, the measurement is aborted. Not supported ...