Search Entire Site

  • Search Within

Search Results

Showing 1-10 of 187 results
Accessing Properties - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/accessing-properties/
In LabVIEW, LabVIEW NXG, and LabVIEW Communications System Design Suite, you can find properties in niUSRP Properties. To access them, complete the following steps: Open a block diagram. Navigate to the ...

Why Doesn't the USRP Device Appear in MAX? - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/appear-max-usrp-device/
MAX only supports USRP-2940/2942/2943/2944/2945 and USRP-2950/2952/2953/2954/2955 devices configured with a PCI Express connection. If you are using a USRP device configured with an Ethernet connection, ...

Configuring an MTU Size Greater than 1,500 Bytes - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/configuring-mtu-greater-than-1500-bytes/
To configure a maximum transmission unit (MTU) size greater than 1,500 bytes, complete the following steps: Enable the jumbo frames option of the Ethernet interface card. Select Control PanelNetwork and ...

Why Doesn't the USRP Device Appear in the NI-USRP Configuration Utility? - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/device-appear-in-config-utility/
Check the connection between the USRP device and the computer. Ensure that the USRP device is powered on and connected to a computer before you power on the computer.

Why Doesn't the Device Power On? - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/device-power-on/
Verify that the power supply is functional by substituting a different adapter. Verify that the power switch on the front of the device is engaged.

Why Do I Receive an Enumeration Error? - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/enumeration-error/
If you are using a desktop computer with the NI-USRP instrument driver installed, it is possible that there is a compatibility issue between your computer and the PCIe card. Complete the following steps ...

Why Don't NI-USRP Examples Appear in the NI Example Finder in LabVIEW? - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/examples-in-ni-example-finder/
NI-USRP does not install examples into the NI Example Finder. You can access NI-USRP examples from the following locations: Content Type Description LabVIEW LabVIEW NXG 3.1 or LabVIEW Communications System ...

Synchronizing with the NI-USRP Driver - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/synchronizing-usrp-driver/
Complete the following steps to configure and synchronize the MIMO system: Open the receive (RX) session by specifying the IP address of each USRP device. Separate each IP address with a comma. Set the ...

Why Does USRP2 Appear Instead of the USRP Device in the NI-USRP Configuration Utility? - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/usrp2-appear-config-utility/
An incorrect IP address on the computer may cause this error. Check the IP address and run the NI-USRP Configuration Utility again. An old FPGA or firmware image on the device may also cause this error. ...

Using NI-USRP in LabVIEW NXG and LabVIEW Communications System Design Suite - NI-USRP 19.0 Manual www.ni.com/documentation/en/ni-usrp/19.0/manual/using-ni-usrp-nxg-comms/
Complete the following steps to develop an NI-USRP application in LabVIEW NXG or LabVIEW Communications System Design Suite: Open an existing or new VI. Select the Diagram tab. From the palette, locate ...