Search Results

Showing 1-10 of 14,336 results
Upgrading or Downgrading LabVIEW with NI-DAQmx www.ni.com/tutorial/54102/en/
Follow the steps in this guide to properly upgrade or downgrade your version of LabVIEW when using NI-DAQmx. This process ensures that your DAQ code runs correctly, your DAQ palett...

Aligning the Antennas - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/aligning-the-antennas/
Antenna alignment improves the repeatability and accuracy of your test. The reference antenna data assumes that the antennas are perfectly aligned, so alignment must be performed for each antenna setup. ...

Attaching the Measurement Antenna - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/attaching-measurement-antenna/
Mount the measurement antenna to the measurement antenna fixture as shown in the following figure. Measurement Antenna FixtureAlignment KnobAlignment KnobMeasurement Antenna1.85 mm (m)-to-1.85 mm (m) Cable, ...

Attaching the Reference Antenna - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/attaching-reference-antenna/
The reference antenna verifies the functionality and integrity of the system during system calibration and ensures that the system is ready for testing your DUT. Mount the reference antenna to the azimuth ...

Getting Started With Autonomous Position Sweeping - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/autonomous-position-sweeping/
With autonomous position sweeping, the measurement initiation is triggered by the positioner instead of the test execution engine. This mode drastically reduces test time. The motor control sends a digital ...

Connecting Internal RF Cables - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/connecting-internal-cables/
Connect one end of two 2.4 mm (m)-to-2.4 mm (m) cables to the interior chamber rear bulkhead 1A and 2A ports. Route the opposite end of the cables through the correct locations on the positioner, as shown ...

Getting Started with Step-by-Step Position Sweeping - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/step-by-step-position-sweeping/
With step-by-step position sweeping, sweeping is exclusively controlled by the test execution engine which consumes a list of predefined positions and sequentially performs a measurement at each point. ...

Performing System Calibration - mmWave OTA Validation Test Reference Architecture www.ni.com/documentation/en/mmwave-ota-validation-test-reference-architecture/latest/user-manual/system-calibration/
Use the RF System Calibration Assistant to perform a full system calibration on all the mmWave OTA Validation Test Reference Architecture hardware components. NI recommends performing system calibration ...

Using NI Compare with Source Control Providers - NI Compare 4.0 Manual www.ni.com/documentation/en/ni-compare-tool/latest/compare/using-ni-compare-tool-with-source-control-providers/
Before beginning this task, make sure the computer on which you are running NI Compare includes a source control provider. Complete the following steps to configure a source control provider to use NI ...

Comparing Files - NI Compare 4.0 Manual www.ni.com/documentation/en/ni-compare-tool/latest/compare/comparing-files/
Complete the following steps to select two files to compare with NI Compare: Ensure you have a project open and locate two files you want to compare on the Project Files tab. You can compare files with ...